Images are representations only.

Meter, Turbine, 4 Inch, Guardsman™ G Series, Model K2BE - Spare Parts

Brand: Guidant
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.

It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.

Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.

They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.

Note: Different features and requirements are available based on where a unit is manufactured.

Throughout this document, manufacturing locations are denoted in parentheses after a feature.

You must place your order with the noted location to receive a unit with the specific feature.
Features
  • 1.5" to 4" Guardsman™ (G) Series
    • Stainless Steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Tungsten carbide bearings system provides longlife on low lubricating fluids
    • Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
    • 125-250 AARH flange face finish
  • 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
    • Stainless-steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
    • Integral-strate-plate flow conditioner (LSJ models)
    • Horizontal or vertical installation
    • Turbine Meter Diagnostics when used with AccuLoad III
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.

It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.

Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.

They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.

Note: Different features and requirements are available based on where a unit is manufactured.

Throughout this document, manufacturing locations are denoted in parentheses after a feature.

You must place your order with the noted location to receive a unit with the specific feature.
Features
  • 1.5" to 4" Guardsman™ (G) Series
    • Stainless Steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Tungsten carbide bearings system provides longlife on low lubricating fluids
    • Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
    • 125-250 AARH flange face finish
  • 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
    • Stainless-steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
    • Integral-strate-plate flow conditioner (LSJ models)
    • Horizontal or vertical installation
    • Turbine Meter Diagnostics when used with AccuLoad III
Close

Displaying prices & availability for Ohio, United States 43201 in USD. Change location.

Models matching criteria: 39
006110-002
Screw, #10-32 x ¼", (UL/CSA version only) - Item 30
Contact for Availability
060060-001
Nut, Hex, ¼"-20, UNC-2B (ATEX version only) - Item 28
Contact for Availability
006621-001
Washer, Lock, ¼" (ATEX version only) - Item 25
Contact for Availability
009544-401
Screw, #10-32 x ¼" - Item 20
Contact for Availability
013403-200
Gasket, Conduit Box - Item 13
Contact for Availability
230663-101
Preamplifier: Preamplifier: PA-6, 12 to 24 VDC - Item 1 view more
  • Recommended Stock
Contact for Availability
543195-200
Label: Label: UL/CSA - Item 12
Contact for Availability
540296-201
Bearing, Rotor - Item 19
Contact for Availability
543196-100
Cover, Conduit Box: Cover, Conduit Box: UL/CSA - Item 10
Contact for Availability
540244-101
Coil, Pickup: Coil, Pickup: Mating Connector with Leads (High Temp - Item 7 view more
  • Recommended Stock
Contact for Availability
543192-203
Clip, Retaining - Item 6
Contact for Availability
540305-208
Bearing, Platform: Bearing, Platform: Smooth - Item 4 view more
  • Recommended Stock
Contact for Availability
645030-452
Connector, (1-5) - Item 2
Contact for Availability
645030-453
Connector, (6-10) - Item 3
Contact for Availability
543256-200
Box, Conduit - Item 5
Contact for Availability
644327-401
Coil, Pickup: Coil, Pickup: -100°F to +225°F - Item 7 view more
  • Recommended Stock
Contact for Availability
641512-401
Coil, Pickup: Coil, Pickup: -100°F to +400°F (High Temperature Version) - Item 7 view more
  • Recommended Stock
Contact for Availability
544156-210
Cone, Downstream: Cone, Downstream: Unidirectional and Bidirectional - Item 8 view more
  • Note 1: Due to a change in the design of this meter in December of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5216, and special serial numbers up to and including 200822 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
  • Note 2: Should either an upstream or downstream cone require replacement on a previous design meter, it will be necessary to replace both at the same time. Cones on current design meters can be replaced individually
Contact for Availability
544155-201
Cone, Upstream, 316 Stainless Steel - Item 9
Contact for Availability
544057-101
Cover, Conduit Box: Cover, Conduit Box: ATEX – Manufactured in USA - Item 10
Contact for Availability
544057-102
Cover, Conduit Box: Cover, Conduit Box: ATEX – Manufactured in Germany - Item 10
Contact for Availability
643243-403
Screw, Set, #6-32 x ¼" - Item 11
Contact for Availability
544056-201
Label: Label: ATEX – Manufactured in USA - Item 12
Contact for Availability
544056-202
Label: Label: ATEX – Manufactured in Germany - Item 12
Contact for Availability
640704-001
Nut - Item 15
Contact for Availability
641069-474
O-Ring - Item 16 view more
  • Note 7: O-Ring not required with Stainless Steel Housing
Contact for Availability
644420-402
Ring, Retaining - Item 17 view more
  • Recommended Stock
Contact for Availability
544163-190
Rotor Assembly: Standard: Rotor Assembly: Standard: Current Design - Item 18 view more
  • Recommended Stock
  • Note 1:  Due to  a  change in  the  design of this  meter    in  December of 1987, it is  necessary to  determine whether your meter is of current or previous design. Standard serial numbers up to and including 5216, and special serial numbers up to and including 200822 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
Contact for Availability
544163-192
Rotor Assembly: Standard: Rotor Assembly: Standard: Previous Design - Item 18 view more
  • Recommended Stock
  • Note 1:  Due to  a  change in  the  design of this  meter    in  December of 1987, it is  necessary to  determine whether your meter is of current or previous design. Standard serial numbers up to and including 5216, and special serial numbers up to and including 200822 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
Contact for Availability
544167-101
Stator Assembly, 316 Stainless Steel - Item 21 view more
  • Note 4: If problems are encountered during installation of stator, please contact the Factory, (814) 898-5000
Contact for Availability
644541-401
Pin, Dowel, ⅛ x ⅜" - Item 22
Contact for Availability
543643-202
Washer, Thrust: Washer, Thrust: Unidirectional and Bidirectional - Item 24 view more
  • Recommended Stock
Contact for Availability
550770-001
Washer, Inverted (ATEX version only) - Item 26
Contact for Availability
550773-001
Stud (ATEX version only) - Item 27
Contact for Availability
544058-101
Wire, Ground, (UL/CSA version only) - Item 29
Contact for Availability
544168-101
Unidirectional, Standard Rotor, Smooth Bearing
Contact for Availability
544168-102
Bidirectional, Standard Rotor, Smooth Bearing
Contact for Availability
Consult Factory - See Note 3
Housing - Item 14 view more
Note 3: Consult Factory, 814 898-5000, provide model no. and serial no. and advise:
  1. Uni or Bidirectional
  2. Housing Material
  3. Flange Material
  4. Flange Class (Pressure)
  5. Number of Pickup Coil Bosses
  6. Type of Flange
Contact for Availability
645416-401
Screw, Set, #10-32 x ¼" Socket - Item 23 view more
  • Note 5: Apply a small amount of Loctite (Part No. 643917-401) to set screw before installing
Contact for Availability
Close

Specifications

Brand

Repeatability

  • ± 0.02 % over the normal flow range

End Connections

  • Class 150 and 300 American Society of Mechanical Engineers (ASME) B16.5, 125-250 Arithmetic Average Roughness Height (AARH) finish raised-face (RF) flanges
  • Class 150, 300, 600, 900 ASME B16.5, 125-250 AARH finish raised face (RF) flanges
  • PN 16, 25 and 40 DIN 2526 Form C flange
  • PN 63 and 100 DIN 2526 Form E flanges
Close