Images are representations only.

Gate-Pak® Injector EI-0755-1 Spare Parts

Brand: Honeywell Process Solutions
Lubrizol Performance Systems™ has supplied a variety of fluid measurement and control systems for over 35 years. Our traditional market is the gasoline market; specifically the fuel additives sector. Before the introduction of the Gate-Pak® Injector, fuel additives were typically metered into gasoline by metering pumps.

While acceptable before the Gate-Pak introduction, metering pumps have inherent problems with leaks, constantly changing calibration, seals that can leak to atmosphere, and no means of proving flow. As fuel additive technology advanced, it became more critical for the exact amount of additive to be injected into the fuel and the elimination of the inherent problems with metering pumps. Thus, the Gate-Pak Injector became and still is the injection system of choice at virtually all the worldwide gasoline marketers. The Gate-Pak Injector is a simple, piston type metering system with only three moving parts.

All wetted parts are either stainless steel or Teflon® and are compatible with the vast majority of chemicals and additives. Each injector is factory tested and calibrated to our customer’s specifications. These features combined have made the Gate-Pak Injector highly accurate and highly reliable with very little maintenance. As discussed above, the precise amount of additive or chemical injected into a product stream is critical. For example, in the case of gasoline additives, if the injection system delivers too little additive, the gasoline will not reach the performance benefits which the gasoline marketer has advertised. Even worse is the reverse case; i.e. the injection system delivers too much additive. This case increases cost by consuming too much additive but also can generate new problems in the engine which can decrease performance.

Both can have a major detrimental impact on the marketer. The Gate-Pak Injector provides both the accuracy and reliability that the gasoline marketers require. To compliment your Gate-Pak® Injector system Lubrizol Performance Systems has developed the Additive Data And Control (ADAC) v2 monitoring system. The ADAC v2 system is a complete package, consisting of an explosionproof (or Nema 4) hardware and custom software, designed to easily provide accurate additive reports. Lubrizol Performance Systems manufactures two additional injection systems; the ABC® Injector and the patented Blend-Pak® Plus Injector.

Both provide the accuracy and reliability of the Gate-Pak Injector but add additional features such as meters, alarms, and communications. Also, Lubrizol Performance Systems designs and manufactures Wild Stream® Blending systems for blending different grades of gasoline. These systems can also blend oxygenate into gasoline which is becoming more prevalent due to the stricter Clean Air regulations. Please contact your Lubrizol Performance Systems distributor or Lubrizol Performance Systems itself if more information is desired.
show more
Lubrizol Performance Systems™ has supplied a variety of fluid measurement and control systems for over 35 years. Our traditional market is the gasoline market; specifically the fuel additives sector. Before the introduction of the Gate-Pak® Injector, fuel additives were typically metered into gasoline by metering pumps.

While acceptable before the Gate-Pak introduction, metering pumps have inherent problems with leaks, constantly changing calibration, seals that can leak to atmosphere, and no means of proving flow. As fuel additive technology advanced, it became more critical for the exact amount of additive to be injected into the fuel and the elimination of the inherent problems with metering pumps. Thus, the Gate-Pak Injector became and still is the injection system of choice at virtually all the worldwide gasoline marketers. The Gate-Pak Injector is a simple, piston type metering system with only three moving parts.

All wetted parts are either stainless steel or Teflon® and are compatible with the vast majority of chemicals and additives. Each injector is factory tested and calibrated to our customer’s specifications. These features combined have made the Gate-Pak Injector highly accurate and highly reliable with very little maintenance. As discussed above, the precise amount of additive or chemical injected into a product stream is critical. For example, in the case of gasoline additives, if the injection system delivers too little additive, the gasoline will not reach the performance benefits which the gasoline marketer has advertised. Even worse is the reverse case; i.e. the injection system delivers too much additive. This case increases cost by consuming too much additive but also can generate new problems in the engine which can decrease performance.

Both can have a major detrimental impact on the marketer. The Gate-Pak Injector provides both the accuracy and reliability that the gasoline marketers require. To compliment your Gate-Pak® Injector system Lubrizol Performance Systems has developed the Additive Data And Control (ADAC) v2 monitoring system. The ADAC v2 system is a complete package, consisting of an explosionproof (or Nema 4) hardware and custom software, designed to easily provide accurate additive reports. Lubrizol Performance Systems manufactures two additional injection systems; the ABC® Injector and the patented Blend-Pak® Plus Injector.

Both provide the accuracy and reliability of the Gate-Pak Injector but add additional features such as meters, alarms, and communications. Also, Lubrizol Performance Systems designs and manufactures Wild Stream® Blending systems for blending different grades of gasoline. These systems can also blend oxygenate into gasoline which is becoming more prevalent due to the stricter Clean Air regulations. Please contact your Lubrizol Performance Systems distributor or Lubrizol Performance Systems itself if more information is desired.
114 models matching criteria
PRESSURE GAUGE (0-160), Part ID 10 - Gate-Pak® Calibration Test Kit
Out of Stock
Ball valve mounting block, Part ID 2 - Tube Fittings
In Stock
1/4" SS flat washer, Part ID 4 - Tube Fittings
In Stock
Tube fitting adapter (long), Part ID 15 - Tube Fittings
In Stock
Label, Model/Serial Number, Part ID 27 - Tube Fittings
In Stock
Label, Filter, Part ID 27b - Tube Fittings
In Stock
Label, Outlet, Part ID 27d - Tube Fittings
In Stock
Cylinder, Part ID 1 - Cylinder Assembly Parts show more
  • 5 inch length 
  • 6 inch 
  • 7 inch 
  • 8 inch
In Stock
Bottom end cap, Part ID 2 - Cylinder Assembly Parts
In Stock
Top end cap, Part ID 3 - Cylinder Assembly Parts
In Stock
Piston, Part ID 7 - Cylinder Assembly Parts
In Stock
End cap gasket, Part ID 9 - Cylinder Assembly Parts
In Stock
1/4" lock washer, Part ID 11 - Cylinder Assembly Parts
In Stock
1/4-20 silicone bronze nut, Part ID 12 - Cylinder Assembly Parts
In Stock
Piston, button magnet, Part ID 13 - Cylinder Assembly Parts
In Stock
Retaining ring, button magnet, Part ID 15 - Cylinder Assembly Parts
In Stock
Piston switch J-box, Part ID 3 - Piston Switch Assembly Parts
In Stock
Base Socket- Gate-Tek/PDC module plug in, Part ID 8 - Piston Switch Assembly Parts
In Stock
PDC-21 module(120 VAC), Part ID 9 - Piston Switch Assembly Parts
In Stock
Solenoid Assembly (Green Body), Part ID 1 - Solenoid Assembly Parts
In Stock
Solenoid Coil - 120 VAC(Black Body), Part ID 2 - Solenoid Assembly Parts
In Stock
HOA Switch Assembly 10-00495 (Items 14, 8, 9, 6) Part ID 4 - Solenoid Assembly Parts
In Stock
1/2" Nipple Galvanized, Part ID 5 - Solenoid Assembly Parts
In Stock
Cover and switch assembly, Part ID 7 - Solenoid Assembly Parts
In Stock
HOA switch only, Part ID 8 - Solenoid Assembly Parts
In Stock
Breather/Drain valve, Part ID 9 - Solenoid Assembly Parts
In Stock
Solenoid mount, Part ID 11 - Solenoid Assembly Parts
In Stock
Cover only, Part ID 14 - Solenoid Assembly Parts
In Stock
Lock washer, Part ID 2 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Top end cap, Part ID 3 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Small “O” ring - Teflon, Part ID 6 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Spring, Part ID 7 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Spool valve assembly, Part ID 8 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Check valve spring, Part ID 12 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Check valve “O” ring - Teflon Encapsulated, Part ID 14 - Spool Valve - Check Valve - Strainer Parts List
In Stock
Check assembly, Part ID 20 - Spool Valve - Check Valve - Strainer Parts List
In Stock
3/8"MNPT X 1/4"FNPT REDUCING NIPPLE, Part ID 3 - Gate-Pak® Calibration Test Kit
In Stock
1/4" TUBE X 1/4" FNPT, Part ID 6 - Gate-Pak® Calibration Test Kit
In Stock
1/4"X1/4"X1/4" FNPT ELBOW, Part ID 9 - Gate-Pak® Calibration Test Kit
In Stock
(2) GRADUATED CYLINDERS 1000 ml, PLASTIC, Part ID 11 - Gate-Pak® Calibration Test Kit
In Stock

Documentation