Description
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.
It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.
Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.
They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.
Note: Different features and requirements are available based on where a unit is manufactured.
Throughout this document, manufacturing locations are denoted in parentheses after a feature.
You must place your order with the noted location to receive a unit with the specific feature.
Features- 1.5" to 4" Guardsman™ (G) Series
- Stainless Steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Tungsten carbide bearings system provides longlife on low lubricating fluids
- Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
- 125-250 AARH flange face finish
- 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
- Stainless-steel measuring chamber and internals
- Locking stator prevents wear and improves performance
- Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
- Integral-strate-plate flow conditioner (LSJ models)
- Horizontal or vertical installation
- Turbine Meter Diagnostics when used with AccuLoad III
Inventory
Displaying price & availability for Ohio, United States in USD Change Location
38 models matching criteria
Nut, Hex #10-32, UNF -2B - Item 28
show more
- Note 7: Replacing Item #13, Part No. 644607-403
In Stock
$1.00USD
Pin, Dowel, ⅛ x ⅜" - Item 20
In Stock
$2.00USD
O-Ring, Buna-N - Item 14
In Stock
$3.00USD
Screw, Set, #6-32 x ¼" - Item 9
In Stock
$5.00USD
Clip, Retaining - Item 4
In Stock
$6.00USD
Washer, Inverted (BASEEFA Version Only) - Item 25
In Stock
$13.00USD
Wire, Ground, UL/CSA Version Only - Item 26
In Stock
$16.00USD
Label: UL/CSA Approvals - Item 10
In Stock
$23.00USD
Screw, #10-32 x ⅜" Set - Item 21
show more
- Note 4: Apply a small amount of Loctite (Part No. 643917-401) to set screw before installing.
In Stock
$27.00USD
In Stock
$29.00USD
Stud (BASEEFA Version Only) - Item 23
In Stock
$72.00USD
Cover, Conduit Box: UL/CSA Approvals - Item 8
In Stock
$110.00USD
Cover, Conduit Box: BASEEFA - Manufactured in the USA - Item 8
In Stock
$141.00USD
Box, Conduit - Item 3
In Stock
$294.00USD
In Stock
$320.00USD
In Stock
$444.00USD
In Stock
$746.00USD
Screw, #10-32 x ¼", UL/CSA Version Only - Item 27
In Stock
Washer, ¼" Lock (BASEEFA Version Only) - Item 24
In Stock
Nut, Hex, ¼"-20, UNC-2B (BASEEFA Version Only) - Item 22
In Stock
Gasket, Cover - Item 11
In Stock
Screw, #10-32 x ¼" - Item 2
In Stock
In Stock
Preamplifier: PA-4, 12 VDC or 24 VDC, Single Channel - Item 1
show more
- Recommended Stock
In Stock
In Stock
Cone, Downstream - Item 6
In Stock
Cone, Upstream - Item 7
In Stock
Cover, Conduit Box: BASEEFA - Manufactured in Germany - Item 8
In Stock
Label: BASEEFA - Manufactured in the USA - Item 10
In Stock
Label: BASEEFA - Manufactured in Germany - Item 10
In Stock
Rotor Assembly: Current Design, 430 Stainless Steel - Item 16
show more
- Recommended Stock
- Note 2: Due to a change in the design of this meter in August of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5015, and special serial numbers up to and including 200779 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
In Stock
Rotor Assembly: Previous Design, 430 Stainless Steel - Item 16
show more
- Recommended Stock
- Note 2: Due to a change in the design of this meter in August of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5015, and special serial numbers up to and including 200779 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
In Stock
In Stock
In Stock
Stator Assembly - Item 19
show more
- Note 3: If problems are encountered during installation of stator, please contact Parts Operation, Attn: Parts Marketing Specialist
In Stock
Internal Parts Kit - Unidirectional - 430 Stainless Steel Rotor
In Stock
Housing - Item 12
show more
Note 1: Consult factory, providing model and serial numbers and advise:
- Uni or Bidirectional
- Housing Material
- Flange Material
- Flange Class (Pressure)
- Number of Pickup Coil Bosses
- Type of Flange
Out of Stock
Nut, #10-32 UNF-2B, Flex-Loc - Item 13
show more
- Note 6: Replaced by Item #28, Part No. 640704-001
Out of Stock
Specifications
Specifications
Brand
Repeatability
- ± 0.02 % over the normal flow range
End Connections
- Class 150 and 300 American Society of Mechanical Engineers (ASME) B16.5, 125-250 Arithmetic Average Roughness Height (AARH) finish raised-face (RF) flanges
- Class 150, 300, 600, 900 ASME B16.5, 125-250 AARH finish raised face (RF) flanges
- PN 16, 25 and 40 DIN 2526 Form C flange
- PN 63 and 100 DIN 2526 Form E flanges