Images are representations only.

Meter, Turbine, 3 Inch, Guardsman™ G Series, Model K2BD - Spare Parts

Brand: TechnipFMC
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.

It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.

Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.

They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.

Note: Different features and requirements are available based on where a unit is manufactured.

Throughout this document, manufacturing locations are denoted in parentheses after a feature.

You must place your order with the noted location to receive a unit with the specific feature.
Features
  • 1.5" to 4" Guardsman™ (G) Series
    • Stainless Steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Tungsten carbide bearings system provides longlife on low lubricating fluids
    • Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
    • 125-250 AARH flange face finish
  • 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
    • Stainless-steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
    • Integral-strate-plate flow conditioner (LSJ models)
    • Horizontal or vertical installation
    • Turbine Meter Diagnostics when used with AccuLoad III
show more
The Smith Meter® Guardsman™ Series Turbine Meter is a bladed, rotor-type meter which utilizes an upstream, cantilevered stator to support the tungsten carbide, bearing-mounted rotor.

It is intended for a wide range of petroleum, petrochemical, and chemical custody transfer measurement applications, such as small product pipelines ranging from Natural Gas Liquids (NGL) to light fuel oils.

Smith Meter Guardsman Series L Models are rimless-type rotor turbine meters that use an upstream stator to support the rotor.

They are intended for use at loading racks to provide the highly accurate measurement required for custody transfer of petroleum liquids.

Note: Different features and requirements are available based on where a unit is manufactured.

Throughout this document, manufacturing locations are denoted in parentheses after a feature.

You must place your order with the noted location to receive a unit with the specific feature.
Features
  • 1.5" to 4" Guardsman™ (G) Series
    • Stainless Steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Tungsten carbide bearings system provides longlife on low lubricating fluids
    • Hydrodynamic thrust balance to minimize friction and wear on thrust bearings which allows for long service life and high accuracy
    • 125-250 AARH flange face finish
  • 1" to 4" Guardsman™ Series Loading Rack (L) Models Turbine Meters
    • Stainless-steel measuring chamber and internals
    • Locking stator prevents wear and improves performance
    • Stainless Steel ball bearings (LB models) and tungsten carbide journal bearings (LJ and LSJ models) provide long life on low lubricating fluids
    • Integral-strate-plate flow conditioner (LSJ models)
    • Horizontal or vertical installation
    • Turbine Meter Diagnostics when used with AccuLoad III
38 models matching criteria
Nut, Hex #10-32 - Item 15
In Stock
$1.00USD
Pin, Dowel, 1/8 x 3/8" - Item 22
In Stock
$2.00USD
O-Ring, Buna - Item 16 show more
  • Note 6:  O-Ring not required for Stainless Steel Housings
In Stock
$3.00USD
Screw, #6-32 x 1/4" - Item 11
In Stock
$5.00USD
Clip, Retaining - Item 6
In Stock
$6.00USD
Washer, Inverted (ATEX version only) - Item 26
In Stock
$13.00USD
Ground Wire (UL/CSA version only) - Item 29
In Stock
$16.00USD
Label: UL/CSA Approvals - Item 12
In Stock
$23.00USD
Connector, (1-5) - Item 2
In Stock
$27.00USD
Connector, (6-10) - Item 3
In Stock
$27.00USD
Screw, #10-32 x 3/8" Set - Item 23 show more
  • Note 5: Apply small amount of Loctite (Part No. 643917-401) to set screw before installing
In Stock
$27.00USD
Ring, Retaining:302 Stn. Stl - Item 17 show more
  • Recommended Stock
In Stock
$29.00USD
Stud (ATEX version only) - Item 25
In Stock
$72.00USD
Cone, Upstream, 316 Stn. Stl., Current Design - Item 9 show more
  • Note 1: Due to a change in the design of this meter in August of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5015 and special serial numbers up to and including 200779 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
  • Note 2: Should either an upstream or downstream cone require replacement on a previous design meter, it will be necessary to replace both at the same time. Cones on current design meters can be replaced individually.
In Stock
$84.00USD
Cone, Downstream:Unidirectional and Bidirectional - Item 8 show more
  • Note 1:  Due to a change in the design of this meter in August of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5015 and special serial numbers up to and including 200779 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator.
  • Note 2:  Should either an upstream or downstream cone require replacement on a previous design meter, it will be necessary to replace both at the same time. Cones on current design meters can be replaced individually.
In Stock
$100.00USD
Cover, Conduit Box: UL/CSA Approvals - Item 10
In Stock
$110.00USD
Washer, Thrust:Unidirectional and Bidirectional - Item 24 show more
  • Recommended Stock
In Stock
$116.00USD
Cover, Conduit Box: ATEX – Manufactured in U.S.A. - Item 10
In Stock
$141.00USD
Box, Conduit - Item 5
In Stock
$294.00USD
Bearing, Platform: Smooth - Item 4 show more
  • Recommended Stock
In Stock
$316.00USD
Coil, Pickup: Mating Connector with Leads (High Temp. Version) - Item 7
In Stock
$320.00USD
Coil, Pickup: -100°F to 225°F - Item 7
In Stock
$444.00USD
Bearing, Rotor - Item 19
In Stock
$448.00USD
Coil, Pickup: -100°F to 400°F (High Temperature Version) - Item 7
In Stock
$746.00USD
Stator Assembly, 316 Stn. Stl. . - Item 21 show more
  • Note 4: If problems are encountered during installation of stator, please contact Factory, (814) 898-5000
In Stock
$1,351.00USD
Rotor Assembly, Standard:Current Design - Item 18 show more
  • Due to a change in the design of this meter in August of 1987, it is necessary to determine whether your meter is of current or previous design. Standard serial numbers up to and including 5015 and special serial numbers up to and including 200779 are considered previous design. Numbers higher than those are current design. These numbers can be found on the nameplate of the meter and on the stator
In Stock
$4,234.00USD
Screw, #10-32 x 1/4" (UL/CSA version only) - Item 30
In Stock
Nut, Hex, 1/4"-20 (ATEX version only) - Item 28
In Stock
Washer, 1/4" Lock (ATEX version only) - Item 27
In Stock
Screw, #10-32 x 1/4" - Item 20
In Stock
Gasket, Conduit Box - Item 13
In Stock
Preamplifier: PA-6, 12 to 24 Vdc - Item 1 show more
  • Recommended Stock
In Stock
Cover, Conduit Box: ATEX – Manufactured in Germany - Item 10
In Stock
Label: ATEX – Manufactured in U.S.A. - Item 12
In Stock
Label: ATEX – Manufactured in Germany - Item 12
In Stock
Internal Parts Kits: Unidirectional – Smooth Bearing
In Stock
Internal Parts Kits: Bidirectional – Smooth Bearing
In Stock
Out of Stock

Specifications

Brand

Repeatability

  • ± 0.02 % over the normal flow range

End Connections

  • Class 150 and 300 American Society of Mechanical Engineers (ASME) B16.5, 125-250 Arithmetic Average Roughness Height (AARH) finish raised-face (RF) flanges
  • Class 150, 300, 600, 900 ASME B16.5, 125-250 AARH finish raised face (RF) flanges
  • PN 16, 25 and 40 DIN 2526 Form C flange
  • PN 63 and 100 DIN 2526 Form E flanges